MODERN 28″ Swing, 120″ Between Centers, BNC-28120A 6″ Bore CNC Flat Bed Heavy Duty Teach Type Lathe C/W: FAGOR 8055 Conversational Controls

SPECIFICATIONS:

• SWING OVER BED 28″ • SWING OVER GAP 35-2/5″ • SWING OVER CROSS SLIDE 18″ • CENTERS HEIGHT 14″ • WIDTH OF BED 22″ • DISTANCE BETWEEN CENTERS 120″ • SPINDLE SPEED , AUTOMATIC RANGE CHANGE 30 – 2000 RPM • SPINDLE NOSE A2-11 • SPINDLE BORE 6.02″ • TAPER ROLLER P5 • Z TRAVEL 124″ • X TRAVEL 16.5″ • CROSS SLIDE WIDTH 8-1/2″

TAILSTOCK

• MAIN MOTOR AC (SPINDLE) 29.33 HP • XZ FEED MOTOR 2.5HP • COOLANT PUMP 1/8HP • AUTO LUBE PUMP 1/16HP • RAPID TRAVERSE X/Z 236 Z 315 IPM • POSITIONING ACCURACY 0.0002″ • REPEATABILITY 0.0001″ • SPINDLE TURNOUT 0.0001″ • CUTTING TOOL ALLOWANCE 1″ X 1″ • Z BALL SCREW 50mm X 10mm C5 • X BALL SCREW 25mm X 5 mm C5 • MACHINE WEIGHT 22,260 lbs. • FLOOR SPACE 120″W X 280″L (with chip conveyor) • WORK WEIGHT CAPACITY WITH TAILSTOCK 6,600 LBS.

COMPLETE WITH:

• RUGGED CAST IRON CONSTRUCTION • FAGOR 8055TC CONTROL, • 11″ VGA HIGH RES. COLOR MONITOR • CNC AND MANUAL OPERATION • INTEGRATED PLC • RUN FIRST COMPONENT MANUALLY AND THEN • 8 BIT BUS, 32K RAM • THE REST AUTOMATICALLY IMPERIAL AND METRIC THREADING • SERIAL PORT (RS-232 COMMUNICATION) • AUTO LUBRICATION SYSTEM • TEACH IN MODE • HARDENED AND GROUND GEARS, SHAFTS & WAYS • SEMI-AUTOMATIC, AUTOMATIC CYCLE • EASY MANUAL TURNING OF RADIAL, CHAMFERS AND PART PROGRAM MODES TAPER, FACING AND GROOVING • AUTOMATIC ACCELERATION/DECELER. • TOOL RADIUS AND GEOMETRY COMPENSATION • RAPID TRAVERSE • INFINITE VARIABLE SPEED • SELF DIAGNOSTIC ROUTINES • INTERNAL DIGITAL READOUT • AUTOMATIC HOME SEARCHING • PROGRAM INPUT RS-232 OR FLOPPY DISK(ON REQUEST) • CONSTANT SURFACE SPEED

• ALL CASTINGS ARE MADE OF HIGH QUALITY MEEHANITE STEEL PROPERLY STRESS RELIEVED. ALWAYS BEEN DESIGNED WITH HEAVY INTERNAL RIBBING AND LARGE THICK WALL TO PROVIDE STABILITY AT HIGH RPM AND RIGIDITY FOR DEEP CUT.

• THE SPINDLE SUPPORTED ON TWO OPPOSITE HIGH PRECISION TAPER ROLLER BEARINGS. ALL GEARS ARE MADE OF Cr-Ni STEEL, HARDENED AND GROUND. FORCED LUBRICATION SYSTEM IN HEADSTOCK. • CSA ELECTRICS • ALL GAP BED • HIGH PRECISION BALLSCREWS • HYDRAULIC TURRET TOOL POST • LARGE VOLUME COOLANT TANK • AUTO LUBRICATION UNIT FOR ALL BEARING • SURFACES AND BALLSCREWS • TRAVELLING FRONT DOOR FULL-CLOSED (SINGLE) INTERLOCKED WITH CARRIAGE • EXTERNAL COOLING SYSTEM • HARDNESS OF BEDWAYS AND CROSS • WAYS MEET HB450 • MANUAL TAILSTOCK • A2-11 SPINDLE NOSE • T-SLOTS IN CROSS SLIDE • WORKLIGHT • CHIP CONVEYOR & WASH DOWN SYSTEM • 5 BAR COOLANT SYSTEM • REAR CHUCK MOUNTING • ROLLER STEADY REST 2 – 11.8 • FAGOR I/0 MODULE • A2-11 TO Di-11 ADAPTOR • 16 3-JAW CHUCK W/ Di-11 BACK PLATE (FRONT MOUNT) • PORTABLE MPG